Walking Pad

How to Turn On a Walking Pad – Step‑by‑Step Guide for Every Brand

You just unpacked your walking pad, remote in hand, ready to walk while you work. But then you stare at the frame and realize you have no clue where the power button is.

Or maybe your remote stopped working and you are stuck with a silent machine. I have been there. Over the years I have tested six different brands and helped friends set up theirs.

This guide covers every common scenario so you can get moving in under a minute.

The Universal Steps to Power On Any Walking Pad

Illustration showing step-by-step process to power on a walking pad including plugging in and pressing power button. — Follow these universal steps to get your walking pad started in under a minute.

Every walking pad needs the same three things before it will turn on:

Plug it in. Connect the power cord to the pad and to a wall outlet. Some pads have a separate adapter; make sure that is secure.
Press the power button. On most models the main power switch is on the side of the frame near the front. It might be a rocker switch or a small push button. Flip it to “on.”
Insert the safety key (if included). Many walking pads have a magnetic safety key that must be attached to the console or a designated slot. The pad will beep but not start unless this key is in place.

After these steps, press the “start” button on the remote or console. The belt should begin moving slowly. If nothing happens, check the brand‑specific instructions below.

Brand‑Specific Instructions for Common Walking Pads

Generic advice only gets you so far. Here is exactly where to find the power button and what to press for the most popular brands.

How to Turn On a KingSmith Walking Pad

Illustration highlighting the power button location on a KingSmith walking pad with remote. — The power switch on a KingSmith walking pad is on the left side near the front.

Power button location: On the left side of the frame near the front. It is a small black rocker switch.
Remote: Point the remote at the front of the pad and press the power icon once. The display lights up. Then press the start (play) button.
Safety key: A round magnet must be on the console. Without it the pad will beep but refuse to start.

How to Turn On a Urevo Walking Pad

Power button location: Under a rubber flap on the right side of the frame. Flip it up and toggle the switch.
Remote: Press and hold the power button on the remote for 2 seconds. A beep confirms the pad is ready. Then tap start.
Without remote: Urevo pads have a manual button on the console. Press and hold it for 3 seconds to power on, then tap it again to start walking.

How to Turn On a Yagud Walking Pad

Power button location: On the front underside of the frame. You might need to bend down to see it. It is a round push button.
Remote: Open the battery compartment first – some Yagud remotes have a plastic tab you must remove. Then press power once, wait for the display, and press start.
Note: Yagud pads often require the remote to be paired. If the pad does not respond, press the pair button on the remote and the frame button simultaneously for 5 seconds.

How to Turn On an Akluer Walking Pad

Power button location: On the back of the pad, near the power cord inlet. It is a standard toggle switch.
Remote: Press the power button (the one with a circle icon). The display shows “0.0.” Then press the plus button to start the belt.
Safety key: Akluer pads use a U‑shaped magnetic key that clips onto the side. If the key is missing, the pad will not turn on.

How to Turn On a Pitpat Walking Pad

Power button location: On the top center of the console. It is a large silver button.
Remote: Press the power button once. The LED lights up blue. Then press the start button (triangle icon).
Troubleshooting: If pressing the power button does nothing, check that the remote batteries are installed correctly. Many Pitpat remotes use a CR2032 coin cell.

How to Turn On a Deerrun Walking Pad

Power button location: On the left side of the frame near the front, behind a small rubber cover.
Remote: Press the power button once. The pad beeps and the display illuminates. Then press the start button.
Safety key: Deerrun pads have a magnetic strip that attaches to the front of the console. Keep it attached or the belt will stop after a few seconds.

How to Turn On a Freepi Walking Pad

Power button location: On the bottom right edge of the frame. It is a small sliding switch.
Remote: Press the power button (marked with a circle). The display shows “0.0.” Tap the play button to begin.
Without remote: Freepi pads have a touch‑sensitive pad on the console. Touch and hold the center for 3 seconds to turn on, then tap again to start.

How to Turn On a Walking Pad Without a Remote

Illustration depicting methods to turn on a walking pad without a remote, using console buttons or a smartphone app. — Don't have the remote? Use the hidden console buttons or a smartphone app to power on.

Losing the remote or having dead batteries does not mean you are stuck. Here are the manual methods I have used successfully:

Console buttons. Many pads have a hidden button panel under a rubber flap on the front or side. Look for a small power symbol. Press and hold for 2–3 seconds. If the display lights up, use the same button or a separate start button to begin.
Smartphone app. KingSmith and some newer Urevo models support Bluetooth control. Download the brand’s app, pair the pad, and use the on‑screen power button. The pad must already have its main power switch turned on for this to work.
Universal remote. If your walking pad uses infrared, a universal remote can sometimes work. Point it at the front of the pad and try the power codes for the brand.
Battery replacement in the remote. A dead remote is the most common reason for a “no start.” Open the remote, swap in fresh batteries, and try again. Most remotes use CR2032 or AAA batteries.

Common Problems When Turning On and How to Fix Them

Problem	Likely cause	Fix
Pad beeps but belt does not move	Safety key missing or not inserted	Attach the magnetic key to the console. If you have lost it, contact the manufacturer for a replacement.
No display, no sound	Power cord not fully plugged or outlet dead	Check that the cord is firmly pushed into the pad and the wall. Test the outlet with another device.
Remote does nothing	Batteries dead or remote not paired	Replace batteries. For pairing, follow the brand’s instructions (usually pressing two buttons together for 5 seconds).
Pad turns off after a few seconds	Safety key dislodged or belt tension too tight	Reattach the key. If the belt is tight, loosen the rear adjustment bolts slightly.
Power button feels stuck	Dust or debris inside the switch	Unplug the pad, use compressed air to blow out the switch area, then try again.

Preparing Your Walking Pad Before the First Use

Illustration of preparation steps for a new walking pad including unfolding, attaching safety key, and placing mat. — Proper preparation ensures your walking pad works reliably from the first use.

Many new owners try to turn on the pad without unfolding it first. That will not work. Follow these steps before you even touch the power button:

Unfold the deck. Most compact walking pads fold for storage. Release the locking latch and pull the deck flat until you hear a click.
Lock the hinge. Some pads have a secondary lock pin that prevents the deck from folding during use. Insert it into the hole near the hinge.
Attach the safety key. Find the magnetic key in the box. Snap it onto the console. Without it, the safety circuit stays open.
Place the pad on a flat surface. An uneven floor can cause the pad to shut off automatically.
Plug in the power cord. Make sure the cord is not pinched under the frame.

Only after these steps should you press the power button. If you do everything in order, the pad will turn on without drama.

What to Do After Turning On – Initial Setup and Noise Reduction

Once the belt is moving, take a minute to set things right:

Calibrate the speed. Start at the slowest setting (0.5–1 km/h). Walk at that pace for 30 seconds to let the motor warm up. Then increase gradually.
Check belt alignment. If the belt drifts to one side, use the hex wrench that came with the pad to adjust the rear roller bolts. Turn the left bolt clockwise to move the belt right, or the right bolt clockwise to move it left.
Reduce noise for downstairs neighbors. A walking pad without a mat sounds like thunder to the people below. Put a thick rubber mat under the pad. Also make sure the pad is sitting on concrete or a solid wood subfloor – not on a hollow floor. If the belt makes a scraping sound, lubricate it with silicone spray (follow the manual for placement).
Tighten loose parts. After the first few walks, check all screws on the frame. Vibration can loosen them over time. Tighten with a screwdriver to eliminate rattles.

Frequently Asked Questions

Can I turn on the walking pad if the remote is lost?

Yes. Check the console for a hidden power button. Many pads have one under a rubber flap.

If that does not work, try the brand’s smartphone app (if available) or buy a replacement remote from the manufacturer.

Why does my walking pad beep but not start?

The safety key is almost certainly missing. Locate the key and attach it to the designated spot on the console. If the key is present, it may be damaged.

Try a spare if you have one, or order a new key from the brand.

How long after plugging in does the pad become ready?

Usually 5–10 seconds. You will hear a short beep or see the display light up. If nothing happens after 30 seconds, check the power switch on the frame.

Do I need to calibrate the walking pad before first use?

You do not need to run a calibration routine, but it is smart to walk at the lowest speed for a minute to let the belt settle. This prevents sudden jerking when you increase speed.

Can I use a phone app to turn on my walking pad?

Only a few brands support this. KingSmith’s newer models and some Urevo pads have Bluetooth control. Download the official app, pair the pad, and you can power it on from your phone.

Older models do not have this feature.